Motorcycle Storehouse

Select your bike

BIKE SELECTOR

20 of 78 search results

Sort on:

Sort on:

Dual spindle; Used to machine cases for high lift cams

George's Garage, cam relief tool

#979419

Stock:Yes

Single spindle; Used to machine cases for high lift cams

George's Garage, TC cam relief tool

#979418

Stock:Yes

Used to correctly align ignition switch housing for installation.

George's Garage, ignition switch housing tool

#979475

Stock:Yes

Removes & installs right side pinion shaft crankcase bearing without damage

George's Garage, pinion crankshaft bearing tool

#979470

Stock:Yes

Installs cam shaft needle bearing.
Note: 979461 driver handle required for installation and must be purchased separately

George's Garage, cam bearing installer tool

#979467

Stock:Yes

For use with 979429 clutch spring compressor tool. Makes 979429 compatible with XL Sportster and Buell models.

George's Garage, clutch spring adapter nut

#979430

Stock:Yes

Used to release clutch spring for removal and installation of retaining ring.

Note: Order 979430 adapter separately for use on XL Sportster models.

George's Garage, clutch spring compressor

#979429

Stock:Yes

Adapts 979418 and / or 979419 (99-06) tool so it is compatible with (06-17) hydraulic chain tensioners

George's Garage, cam relief pilot

#979420

Stock:Yes

Removes and installs the wristpin in a controllable process with slide hammer action. No need to use force.

George's Garage, wristpin tool

#979400

Stock:Yes

Adapter only for use on fine-spline sprocket shafts
Note: Use with 979426 sprocket shaft bearing installer tool

George's Garage, sprocket shaft adapter kit

#979472

Stock:Yes

Used to install and remove new wristpin bushings without removing connecting rods from the crankcase. Removes and installs both bushings in less than 5 minutes.

George's Garage, wristpin bushing driver tool

#979409

Stock:Yes

Used to align engine, transmission and swingarm with each other to the correct position.

George's Garage, FLT power train alignment tool

#979459

Stock:Yes

Used to remove & install transmission bearings; Will also remove transm. door without removing the gear set or transm. assembly;
Note: Door bearings must be replaced if using this tool to remove the door only.

George's Garage, transmission door bearing tool

#979445

Stock:Yes

Removes wire type clips; 14mm nose dia.;
Note: Not for use with forged pistons

George's Garage, wrist pin clip tool

#979479

Stock:Yes

Used between primary chain and front motor sprocket to prevent primary movement when loosening & re-torquing sprocket & clutch nuts. Made from POM (a polyoxymethylene polymer), an extremely strong and tough material.

George's Garage, primary drive locking tool

#979436

Stock:Yes

Used to lock the pinion gear for nut removal.

George's Garage, pinion gear locking tool

#979423

Stock:Yes

Can be used with impact air wrenches. -7/8" hex with 1/2" drive. Removes & installs the 1-1/2"-24 hex nut (35211-36 and 35211-91B) transmission mainshaft pulley/sprocket nuts.
Note these nuts are left hand threaded.

George's Garage, transmission / sprocket nut tool

#979438

Stock:Yes

Used to remove & install transmission bearings; Will also remove transm. door without removing the gear set or transm. assembly;
Note: Door bearings must be replaced if using this tool to remove the door only.

George's Garage, transmission door bearing tool

#979444

Stock:Yes

Used to remove & install the main drive gear and main drive gear case bearing

George's Garage, main drive gear tool

#979441

Stock:Yes

Used with 979457 steering head bearing race tool and 979453 wheel bearing race tool

George's Garage, driver handle 12"

#979461

Stock:Yes