BIKE SELECTOR

20 of 232 search results

Sort on:

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 19mm

#580882

Stock:Yes

Used to lock flywheel, of assembled engine. Installs through crank position sensor. Great for use with compression leakdown testing and other service operations where flywheels must be locked. Note: Incl. highly visible red 'Danger, do not operate' card to prevent someone starting engine.
Jims

JIMS, 'Mighty Bite' flywheel lock

#559408

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 21mm

#580881

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 17mm

#580883

Stock:Yes

Must be ordered separately for 978324 JIMS sprocket shaft seal installer tool. Is included with 978325 JIMS maindrive seal installer tool.
Jims

JIMS, driver handle

#576558

Stock:Yes

Used to install cam bearing. Note: MCS 920542 installation handle is required and sold separately.
Jims

JIMS, cam bearing installer tool

#978289

Stock:Yes

A must for maintaining a long life of balancer drive chains and bearings. Takes the guess-work out of setting up the sprocket & chain assembly on Twin Cam Softail models. This tool must be treated with great care, as you would treat a micrometer.
Jims

JIMS, balancer shaft alignment tool

#978416

Stock:Yes

Used to rotate the assembled engine, fits to sprocket shaft, when doing pushrods or engine timing; With 1/2" drive; Note: Use with hand drivers only. Not to be used with power tools.
Jims

JIMS, sprocket shaft engine rotator

#978501

Stock:Yes

Replacement for 978407 JIMS connecting rod lap set
Jims

JIMS, replacement 1 5/8" OD lap head

#978410

Stock:Yes

Installer only for race of 9028 sprocket shaft bearing; Also used when upgrade converting 03-17 Twin Cam with roller bearing to the earlier 9028 Timken sprocketshaft bearing design Note: See 978519 JIMS crankcase race insert kit for converting 03-17 Twin Cam
Jims

JIMS, sprocket shaft bearing race installer

#978340

Stock:Yes

Used to easily remove the inner Timken bearing from the sprocket shaft without removing shafts from the flywheels
Jims

JIMS, sprocket shaft bearing puller tool

#978327

Stock:Yes

Use with 978411 crankcase lap tool
Jims

Jims, repl. 1 3/4 inch lap head

#978412

Stock:Yes

Installs and removes 23966-54A crank pin nut. Used when rebuilding flywheel assemblies. Machined flat at the receiving end and have a low profile with just adequate length for 100% nut to socket contact to prevent damage to socket or personal injury. Machined from 4130 chromoly steel and heat treated.
Jims

JIMS, flywheel socket 1-5/16 x 1/2 drive

#978431

Stock:No

Used to hold flywheels in vice, with or without left case attached
Jims

JIMS, flywheel holder tool

#978284

Stock:Yes

Used to install the crankshaft assembly into the left crankcase Timken bearing; Note: 978332 socket is required for this tool and must be ordered separately; Note: 978334 (2.060" long) and 978335 (2.500" long) install tools are both required for 77-03 XL, Buell models and must be ordered separately
Jims

JIMS, sprocket shaft bearing installer tool

#978333

Stock:No

Use with MCS 908132 / Repl. 25591-37 pinion shaft bushing & 519008 / OEM 275 dowel pin
Jims

JIMS, pinion bushing installer/drill jig

#978282

Stock:Yes

.105 inch diameter. Used to check pinion and cam gears for pitch diameters. A loose fit results in a clicking noise but a tight fit in a whining noise that may result in gear tooth & bearing damage. For sizing charts, see the OEM H-D service manual.
Jims

JIMS, cam & pinion gear gauge pins .105"

#978298

Stock:Yes

2.500" long. To be used in combination with 978833 sprocket shaft bearing installer tool. These are tools that are additionally required when using JIMS sprocket shaft bearing installer tool MCS 978333 for 77-03 Sportster and 94-02 Buell models. Use tool MCS 978334 to install the bearing until tool runs out of threads, then install tool MCS 978335 to push the bearing the rest of the way. Note: 978334 2.060" long install tool is also required.
Jims

JIMS, sprocket shaft bearing install tool 2.500"

#978335

Stock:Yes

Used to install outer retaining ring on the oil pump drive shaft
Jims

JIMS, oil pump snap ring installer

#978312

Stock:Yes

Removes & installs right side pinion shaft crankcase bearing without damage
George's Garage

George's Garage, pinion crankshaft bearing tool

#979470

Stock:Yes