BIKE SELECTOR

20 of 231 search results

Sort on:

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 19mm

#580882

Stock:Yes

Used to install 989244 crankcase nuts.
Colony

Colony nut install tool

#989245

Stock:Yes

Used to install and remove sprocket shaft bearing race from left side crankcase; Note: Used with 920542 JIMS driver handle
Jims

JIMS, sprocket shaft bearing race tool

#978337

Stock:No

Used to remove OEM 11000134 / 568378 sprocket shaft seal / crankshaft main seal from left engine case without damage. Pulls seal square to the bore by turning a wrench. Note: See 559403 for JIMS installer tool.
Jims

JIMS, sprocket shaft seal puller tool

#569209

Stock:Yes

Used to lock flywheel, of assembled engine. Installs through crank position sensor. Great for use with compression leakdown testing and other service operations where flywheels must be locked. Note: Incl. highly visible red 'Danger, do not operate' card to prevent someone starting engine.
Jims

JIMS, 'Mighty Bite' flywheel lock

#559408

Stock:Yes

Used to bench test Feuling M8 oil pumps (tester will not fit OEM M8 pumps). Used for PSI pressure opens the relief valve. The spring tension can be adjusted to achieve the desired pop-off PSI. Tool includes: air regulator, 0 - 100 psi pressure gauge, plugs for water and oil cooled oil pumps, gasket & needed hardware. Feuling® recommends the oil pump relief valve be seated and sealed from 0-30 psi with full pop-off at 50-60 psi. Note: Will not fit OEM pumps.
Feuling

Feuling, oil pump pressure tester

#588061

Stock:Yes

Used to ream the pressure relief valve seat of the cam plate in all Twin Cam engines and in the oil pump of M8 engines. Compatible with OEM and aftermarket cam plates. Feuling recommends a new relief valve as Feuling 566110 relief valve, spring & roll pin kit. Note: Can be used with 566117 (Twin Cam cam plate) and 588061 (M8 oil pump) pressure relief valve test tools.
Feuling

Feuling, cam plate/oil pump reamer tool

#588062

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 21mm

#580881

Stock:Yes

Optional pin collet for 580880 dowel pin puller tool. Hardened steel. Laser etched for clear identification.
Motion Pro

Motion Pro dowel pin puller 17mm

#580883

Stock:Yes

Must be ordered separately for 978324 JIMS sprocket shaft seal installer tool. Is included with 978325 JIMS maindrive seal installer tool.
Jims

JIMS, driver handle

#576558

Stock:Yes

Used to install cam bearing. Note: MCS 920542 installation handle is required and sold separately.
Jims

JIMS, cam bearing installer tool

#978289

Stock:Yes

A must for maintaining a long life of balancer drive chains and bearings. Takes the guess-work out of setting up the sprocket & chain assembly on Twin Cam Softail models. This tool must be treated with great care, as you would treat a micrometer.
Jims

JIMS, balancer shaft alignment tool

#978416

Stock:Yes

Used to rotate the assembled engine, fits to sprocket shaft, when doing pushrods or engine timing; With 1/2" drive; Note: Use with hand drivers only. Not to be used with power tools.
Jims

JIMS, sprocket shaft engine rotator

#978501

Stock:Yes

Replacement for 978407 JIMS connecting rod lap set
Jims

JIMS, replacement 1 5/8" OD lap head

#978410

Stock:Yes

Installer only for race of 9028 sprocket shaft bearing; Also used when upgrade converting 03-17 Twin Cam with roller bearing to the earlier 9028 Timken sprocketshaft bearing design Note: See 978519 JIMS crankcase race insert kit for converting 03-17 Twin Cam
Jims

JIMS, sprocket shaft bearing race installer

#978340

Stock:Yes

Used to easily remove the inner Timken bearing from the sprocket shaft without removing shafts from the flywheels
Jims

JIMS, sprocket shaft bearing puller tool

#978327

Stock:Yes

Use with 978411 crankcase lap tool
Jims

Jims, repl. 1 3/4 inch lap head

#978412

Stock:Yes

Installs and removes 23966-54A crank pin nut. Used when rebuilding flywheel assemblies. Machined flat at the receiving end and have a low profile with just adequate length for 100% nut to socket contact to prevent damage to socket or personal injury. Machined from 4130 chromoly steel and heat treated.
Jims

JIMS, flywheel socket 1-5/16 x 1/2 drive

#978431

Stock:No

Installs and removes 23969-83 crank pin nut. Used when rebuilding flywheel assemblies. Machined flat at the receiving end and have a low profile with just adequate length for 100% nut to socket contact to prevent damage to socket or personal injury. Machined from 4130 chromoly steel and heat treated.
Jims

JIMS, flywheel socket 1-1/2 x 1/2 drive

#978433

Stock:Yes

Used to hold flywheels in vice, with or without left case attached
Jims

JIMS, flywheel holder tool

#978284

Stock:Yes