Motorcycle Storehouse

Select your bike

BIKE SELECTOR

20 of 274 search results

Sort on:

Sort on:

Used to remove the press-fitted tappet blocks from the right side of the Sportster crankcase. Replaces OEM 95724-57 tool.

JIMS, tappet block puller tool

#978308

Stock:Yes

Dual spindle; Used to machine cases for high lift cams

George's Garage, cam relief tool

#979419

Stock:Yes

Single spindle; Used to machine cases for high lift cams

George's Garage, TC cam relief tool

#979418

Stock:Yes

Used instead of rags. Provides enough plugs to fully seal all Twin Cam and transmission holes to prevent dirt and dust from entering while it is apart during a rebuild or repair.

JIMS, engine & transmission plug kit

#962014

Stock:Yes

Used to rotate the assembled engine, fits to sprocket shaft, when doing pushrods or engine timing; With 1/2" drive;
Note: Use with hand drivers only. Not to be used with power tools.

JIMS, sprocket shaft engine rotator

#978501

Stock:Yes

Used with 4.000" to 4.060" bore with OEM bolt pattern. Used to measure cylinder measurements accurately torque plates are essential. These plates simulate stress conditions when boring and honing, which prevents distortion of cylinders walls once cylinders are back to the installed condition. Plates are lasered with the correct torque sequence.

JIMS, cylinder torque plate kit

#961536

Stock:Yes

Replacement reamer only for 978343 JIMS +.030" breather reamer tool

JIMS, replacement reamer tool

#978429

Stock:Yes

Single spindle; Used to machine cases for high lift cams;
Note: This tool has one spindle cutter and must be re-mounted to clear the opposite cam side;
Note: See 978472 for dual spindle cam relief tool

JIMS, TC cam relief tool. Single spindle

#978471

Stock:Yes

With 12 & 14mm threaded ends. Used to help hold the cylinder head firmly in a workbench vice, through the spark plug hole, to aid in servicing / overhaul work.

JIMS, cylinder head holder tool. 12mm/14mm

#978381

Stock:Yes

Used to install OEM style piston wristpin retaining ring as used in many 73-77 B.T. and XL models

JIMS, wristpin retaining ring tool

#978316

Stock:Yes

Used to install (round wire type) piston wristpin retaining rings MCS 508585 (OEM 22589-83A).

JIMS, wristpin retaining ring tool

#978317

Stock:Yes

Used to drill-out stripped cylinder stud threads, up to 4" bore, in the crankcases. This tool will hold the centerline and squareness. Can be used with engine in the frame when used with a angled head drill.
Note: Helicoils or similar not included.

JIMS, cylinder drill jig assembly

#978267

Stock:No

Supports piston when installing rings and cylinder

JIMS, piston support plate

#978423

Stock:Yes

Used to install rocker arm bushings in rocker arms with or without a press. This tool will install each bushing to the correct depth for best oil control.

JIMS, rocker arm bushing installer tool

#978234

Stock:Yes

Incl. 24mm & 28mm outside diameter aluminum adapters. Billet 6061-T6 aluminum frame provides unmatched strength and stiffness and lower weight. Quick release system presses straight against the retainer to eliminate side loading the valve and keepers. Works on all motorcycle, ATV, UTV, and small engine cylinder heads. Fully adjustable top and bottom. Aluminum lower adjuster will not damage or scratch valves. Includes two universal fork style tips/adapters. Durable blue anodized finish with laser engraved markings. Simple, fast, and easy to use.

Note: See 580891 for 18mm & 28mm outside diameter adapters.

Motion Pro, T-6 valve spring compressor

#580890

Stock:Yes

Used to easily remove and install the wire type wristpin clips without hassle, over-squeezing clip or damage to piston.

Note: Not for use with forged pistons.

JIMS, wrist pin clip tool

#978422

Stock:No

Fits 2 3/4" up to 5" (70mm to 127mm) pistons; Incl. 2 cleaning spurs with sizes: 5/64", 3/32", 1/8", 5/32", 3/16", 1/4", 1.5mm, 1.75mm and 2mm

Lisle, Piston ring groove cleaner

#530799

Stock:Yes

Used with stock 3.75" (3-3/4") to 3.875" (3-7/8") inch bore cyl. with OEM bolt pattern. Used to measure cylinder measurements accurately torque plates are essential. These plates simulate stress conditions when boring and honing, which prevents distortion of cylinders walls once cylinders are back to the installed condition. Plates are lasered with the correct torque sequence.

JIMS, cylinder torque plates

#978213

Stock:Yes

Used to install valve guides equipped with 18046-98 5/16x.530" Steel Grip® valve seals to proper depth.

Note: Use with JIMS 961423 handle (not included).

JIMS, shoulderless valve guide installer tool

#961421

Stock:Yes

For cast iron, manganese bronze, C630 bronze & Ampco-45 bronze; Used to finish hone to correct tolerance

Kpmi, valve guide hone, 4mm

#524529

Stock:Yes