Motorcycle Storehouse

Select your bike

BIKE SELECTOR

20 of 51 search results

Sort on:

Sort on:

Required for Öhlins fork rebuilding and cartridge installation of Öhlins FKS 508 cartridges.
This tool uses a 3/8" drive end and provides easier assembly and disassembly when servicing specific Öhlins forks.
Designed and engineered to be used with the KRT Forks (FF52X), Dynamoto Forks (FGRT 205s), and FKS 508s

Kraus, cartridge seal head driver tool

#984642

Stock:Yes

Fits 37mm fork tubes; Carbon steel with aluminum lock ring; Used to drive fork seals into lower fork leg without hassle; Easy 2-piece design

Motion Pro, Ringer fork seal driver 37mm forks

#547679

Stock:Yes

Fits 48mm fork tubes; Carbon steel with aluminum lock ring; Used to drive fork seals into lower fork leg without hassle; Easy 2-piece design

Motion Pro, Ringer fork seal driver 48mm forks

#547712

Stock:Yes

Used to help assemble and disassemble Springer type front forks

Motion Pro, Springer fork spring tool

#547240

Stock:No

For 39mm fork tubes; Used to help install fork tube plugs on forks with a lot of spring pre-load

Motion Pro, fork spring compressor kit

#547234

Stock:Yes

Used to install fork seals and fork caps without damage to the seal lip. This tool can be used for 35mm, 39mm and 41mm fork tubes. Includes a special 39mm POM cap.

MCS, fork seal & cap installer tool kit

#925557

Stock:Yes

Blue anodized aluminum. Used to install 49mm fork seal squarely into the lower fork leg without seal damage. Also installs dust cover. Will not fit models with upside down forks. Easy to use 2-piece design.

JIMS, 49mm fork seal & dust shield tool

#978513

Stock:Yes

Used to install and remove the rocker studs on Springer forks. Comes with a pilot to simplify removal and installation. Helps prevent damage to the slot of the studs.

MCS, springer rocker stud tool

#925574

Stock:Yes

Used to access and make adjustments to the 45718-60 1-1/2" x 1.5 x 0.47" fork stem nut on Touring models, without removing the radio

JIMS, Touring fork stem nut wrench

#962036

Stock:Yes

Used to help with the Cartridge installation for specific Kraus and Öhlins, cartridges and forks..
Designed and engineered to be used with Kraus KRT forks (FF52X), Kraus Dynamoto forks (FGRT 205s), Öhlins FKS 212, FKS 221, FKS 228, and FKS 508 model forks.
Tool comes with M8x1.25, M10x1.25, and M12x1.25 thread sizes allowing it to be used in other applications as well.

Kraus, cartridge pull rod tool

#984641

Stock:Yes

Springer forks, remove & install rocker bushings

Colony rocker stud bushing tool

#989749

Stock:Yes

Two-piece design; Used to install & remove the races in the frame neck or in the frame cup; The optional 978339 X-tra grip driver spacer fits between both tool pieces, providing outward force, to prevent any tool-slip from the bearing race during the removal action
Note: Order 920542 JIMS driver handle separately
Note: X-tra grip driver available as 978339

JIMS, steering head bearing race tool

#978376

Stock:Yes

For 41mm forks; Used to install fork seals & bushings in fork sliders; Two-piece split design

George's Garage, fork seal & bushing install tool

#979454

Stock:Yes

Used with JIMS 978613 vacuum fork filler tool

JIMS, Mityvac hand vacuum pump kit

#978614

Stock:Yes

Used to change the fork oil in full dressers. Around 2 hours would be expected when doing a fork oil change, this tool makes it around 30 minutes. Will work on all other models as well, except those with upside down or cartridge type forks.
Note 1: The 978614 hand vacuum tool is required for use with the 978613 Vacuum fed fork filling tool.
Note 2: Will not work on upside down or cartridge type forks.

JIMS, vacuum fork filler

#978613

Stock:Yes

Fits 41mm fork tubes; Carbon steel with aluminum lock ring; Used to drive fork seals into lower fork leg without hassle; Easy 2-piece design

Motion Pro, Ringer fork seal driver 41mm forks

#547690

Stock:Yes

This is a front fork & rear shock absorber maintenance tool. It is used to securely hold the front fork slider for maintenance like oil & seal change. It also will hold the rear shock absorber, on body, shaft or shock reservoir, for maintenance work like spring, piston rod, seal head removal etc.
- Designed to make suspension service simple and quick.
- Holds shocks and forks securely while you change oil, re-valve, or change seals.
- Pivoting head holds parts in any position, with mechanical stops every 45 degrees.
- Aluminum Soft Jaw Vise holds cylindrically shaped parts utilizing a 4 point grip system.
- Large side holds 40 mm to 61 mm diameter parts.
- Small side holds 16 mm to 34 mm diameter parts.
- Steel Frame is rigid yet has a small footprint, with 4 pre-drilled holes in the base for secure mounting to a workbench.
- Movable fluid catch pan with mesh insert, and threaded drain bung.
- HOW IT WORKS ON FORKS -
- Soft Jaw Fork Peg holds fork slider up for removal of dust seal and seal retaining clip.
- Repositionable bottom slide bar holds forks compressed while bleeding air (priming cartridge) during reassembly and is an excellent platform for adding, adjusting and taking fork oil level measurements.
- Can be used to assist in removing compression valve assembly (use of stock front axle required).
- HOW IT WORKS ON REAR SHOCK ABSORBERS -
- Holds shock firmly around shock body, shaft or shock reservoir.
- Facilitates removal of piston rod and seal head.
- Facilitates removal of shock reservoir caps, chamber pistons or bladder.
- Holds shock to remove spherical bearings or needle bearings.
- Holds shocks for removal of shock spring.

Motion Pro, Pivot suspension vise tool

#937661

Stock:No

Used to remove and install top fork tube plug that fits inside the fork tube. Prevents damage to the plugs like can occur when a regular wrench is used. Comes with a 1/2" drive.

MCS, upper 41mm fork tube plug socket

#925563

Stock:Yes

For 49mm forks; Used to install fork seals & bushings in fork sliders; Two-piece split design

George's Garage, fork seal & bushing install tool

#979456

Stock:Yes

Fits 45mm fork tubes; Carbon steel with aluminum lock ring; Used to drive fork seals into lower fork leg without hassle; Easy 2-piece design

Motion Pro, Ringer fork seal driver 45mm forks

#547713

Stock:Yes